12V-48V 1800W ZVS Induction Heating Board Module Flyback Driver Heater with coil

Description

12V-48V 1800W ZVS Induction Heating Board Module Flyback Driver Heater with coil
a.imagelink {color:#6f58dd;} a:hover.imagelink {color:#6f58dd;} a:visited.imagelink {color:#B493F1;} a.imagelink img.auctionimage { border: 2px solid #6f58dd; } a:visited.imagelink img.auctionimage { border: 2px solid #B493F1; }
Specification
Name: ZVS Induction Heating Board Module
Product size: 180mm x 90mm x 80mm (Manual measurement, error about 3mm, please understand)
Heater ring inner: 70mm (Recommended crucible + quartz suit, maximum support of 58mm crucible)
Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12V≥10A , 15V above≥15A
Maximum power: 1800W
Maximum current: 40A
Features
This products maximum power 1800W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc..
This induction heating circuit uses 12-48V low voltage DC power supply, maximum current 40A, the most highest power is 1800W. It can work continuously under the condition of good heat dissipation. Due to its moderate power, it can be used by DIY players to give smaller players the parts can be treated by quenching, annealing and other heat treatment. You can also be melted with graphite crucible Kim, Silver, Copper, aluminum and other metal, heating evenly, is fast and very convenient.
In this test, the maximum power is close to 1600W, and the maximum current is 35A. This product is available at under the condition of good heat dissipation, the utility model can work continuously for hours.
Note:
1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.
2. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
3. When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better. (package does not inclues)
4. Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.
5. Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.
6. The minimum input voltage of the module is 12V, it doesn't mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same time conduction, will burn MOS tube;
7. If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.
8. Do not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn out
9. Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage decreases, below 12V is very dangerous
10. Induction heating power is great, so fever is normal, be sure to do a good job of cooling.
11. Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
Package Included
1 x PCB board
1 x 48V copper tube
We only accept the payment by Paypal.
Buyers are required to carefully follow payment instructions on the checkout page, and note down any necessary details on it (e.g. bank account details).
If buyers fail to follow the instructions on the checkout page, We are not liable for any unidentified payments and subsequent delivery delays.
Items will be dispatched within 1 business days after your payment gets cleared
Please pay attention to the ETA time for each delivery service and choose the one which is suitable for you
Buyers will also be able to trace deliveries online with a unique tracking number. While we endeavor to send all our items with tracking numbers, there may be a few smaller items that are not sent with a tracking number.
Buyers have full responsibility to provide us with the correct delivery address on the checkout page before payment is made.
Re-delivery fee may be charged to buyers for items that are undelivered and/or returned to us due to incorrect delivery address or unsuccessful deliveries.
Items will only be delivered during normal working hours (9am to 5pm on weekdays. Delivery is not available on weekends, public holidays or after business hours
All returns should be qualified as following:
Please wait for our confirmation on how the item is to be returned.
The item must retain all original internal and external packaging.
The item itself must not be opened. We acknowledge the external box may have been opened for a visual inspection, but nothing else must be opened or used.
Just prior to returning it to us, ensure that there is nothing (e.g. return paperwork, email copy) stuck on the item or anywhere else inside of the box.
Any postage labels or return paperwork must be stuck on the outside box.
Once the item has been returned, we will need to deduct the initial dispatch and also the return freight charges from your refund.
Refunds will only be processed Paypal,  depending on the original method of payment.
We maintain high standards of excellence service and strive for 100% customer satisfaction! Feedback is very important to us.
You are guaranteed to have your order fully delivered or your money back. Kindly contact us freely if there is any issue with our products
.
If have any questions, Please contact by ebay message.
We care about our valued buyers, if you have any questions, our Customer Service staffs will be very glad to help you. We try our best to reply as soon as possible,Please allow 24 business hours for us to response,tks!
Specification
Name: ZVS Induction Heating Board Module
Product size: 180mm x 90mm x 80mm (Manual measurement, error about 3mm, please understand)
Heater ring inner: 70mm (Recommended crucible + quartz suit, maximum support of 58mm crucible)
Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12V≥10A , 15V above≥15A
Maximum power: 1800W
Maximum current: 40A
Features
This products maximum power 1800W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc..
This induction heating circuit uses 12-48V low voltage DC power supply, maximum current 40A, the most highest power is 1800W. It can work continuously under the condition of good heat dissipation. Due to its moderate power, it can be used by DIY players to give smaller players the parts can be treated by quenching, annealing and other heat treatment. You can also be melted with graphite crucible Kim, Silver, Copper, aluminum and other metal, heating evenly, is fast and very convenient.
In this test, the maximum power is close to 1600W, and the maximum current is 35A. This product is available at under the condition of good heat dissipation, the utility model can work continuously for hours.
Note:
1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose.
2. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
3. When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better. (package does not inclues)
4. Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.
5. Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.
6. The minimum input voltage of the module is 12V, it doesn't mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same time conduction, will burn MOS tube;
7. If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.
8. Do not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn out
9. Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage decreases, below 12V is very dangerous
10. Induction heating power is great, so fever is normal, be sure to do a good job of cooling.
11. Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
Package Included
1 x PCB board
1 x 48V copper tube
PAYMENT
We only accept the payment by Paypal.
Buyers are required to carefully follow payment instructions on the checkout page, and note down any necessary details on it (e.g. bank account details).
If buyers fail to follow the instructions on the checkout page, We are not liable for any unidentified payments and subsequent delivery delays.
SHIPPING
Items will be dispatched within 1 business days after your payment gets cleared
Please pay attention to the ETA time for each delivery service and choose the one which is suitable for you
Terms of Sale
Buyers will also be able to trace deliveries online with a unique tracking number. While we endeavor to send all our items with tracking numbers, there may be a few smaller items that are not sent with a tracking number.
Buyers have full responsibility to provide us with the correct delivery address on the checkout page before payment is made.
Re-delivery fee may be charged to buyers for items that are undelivered and/or returned to us due to incorrect delivery address or unsuccessful deliveries.
Items will only be delivered during normal working hours (9am to 5pm on weekdays. Delivery is not available on weekends, public holidays or after business hours
All returns should be qualified as following:
Please wait for our confirmation on how the item is to be returned.
The item must retain all original internal and external packaging.
The item itself must not be opened. We acknowledge the external box may have been opened for a visual inspection, but nothing else must be opened or used.
Just prior to returning it to us, ensure that there is nothing (e.g. return paperwork, email copy) stuck on the item or anywhere else inside of the box.
Any postage labels or return paperwork must be stuck on the outside box.
Once the item has been returned, we will need to deduct the initial dispatch and also the return freight charges from your refund.
Refunds will only be processed Paypal,  depending on the original method of payment.
ABOUT US
We maintain high standards of excellence service and strive for 100% customer satisfaction! Feedback is very important to us.
You are guaranteed to have your order fully delivered or your money back. Kindly contact us freely if there is any issue with our products
.