10PCS 2S 10A Battery Protection Board 18650 Li-ion Lithium Charger BMS PCM New

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
10PCS 2S 10A Battery Protection Board 18650 Li-ion Lithium Charger BMS PCM New
Popular
Popular
Product Introduction
Description:
Note:
The protection board can not be used for lithium iron phosphate battery, hernia lamp, hand drill battery pack, electric fish battery pack, electric bicycle battery pack, 775 (4A) motor, 1W fish eye LED light, for the combination of the purchase of customers Please pay attention!
The Overcharge voltage range: 4.25-4.35v ± 0.05v
Size: 46.7 * 23 * 3.15mm
Overpressure voltage range: 2.5-3.0v ± 0.05v
Upper working current: 10A
Operating temperature: -40 --- +50 ℃
Upper limit instantaneous current: 20A
Storage conditions: -40-- +80 ℃
Quiescent current: less than 10uA
Effective life: more than 50,000 hours
Internal resistance: less than 300mΩ
Short circuit protection: can be protected, need to charge recovery
Charging voltage: 8.4V-9V
The protection board size and device description;
The size of the protective plate is 46.7 * 23 * 3.15mm
Welding point Description:
B + connected to the battery positive;
B-connected battery negative;
MB connects the battery 1 to the connection point before the battery 2;
P + connected to the charge / discharge side of the positive (charge side / discharge side shared);
P-connect / discharge terminal negative (shared with charge / discharge).
Tips: the battery pack when the battery voltage, capacity, internal resistance must be a good match, the battery voltage in the rated voltage of about 3.7V appropriate, the group did not output a good battery pack, with 8.4V voltage can be charged.
Package Included:
10PCS*2S 10A 7.4V 8.4V Li-ion Lithium 18650 Battery w/Balance BMS Protection PCB Board
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
10PCS 2S 10A Battery Protection Board 18650 Li-ion Lithium Charger BMS PCM New
Product Introduction
Description:
Note:
The protection board can not be used for lithium iron phosphate battery, hernia lamp, hand drill battery pack, electric fish battery pack, electric bicycle battery pack, 775 (4A) motor, 1W fish eye LED light, for the combination of the purchase of customers Please pay attention!
The Overcharge voltage range: 4.25-4.35v ± 0.05v
Size: 46.7 * 23 * 3.15mm
Overpressure voltage range: 2.5-3.0v ± 0.05v
Upper working current: 10A
Operating temperature: -40 --- +50 ℃
Upper limit instantaneous current: 20A
Storage conditions: -40-- +80 ℃
Quiescent current: less than 10uA
Effective life: more than 50,000 hours
Internal resistance: less than 300mΩ
Short circuit protection: can be protected, need to charge recovery
Charging voltage: 8.4V-9V
The protection board size and device description;
The size of the protective plate is 46.7 * 23 * 3.15mm
Welding point Description:
B + connected to the battery positive;
B-connected battery negative;
MB connects the battery 1 to the connection point before the battery 2;
P + connected to the charge / discharge side of the positive (charge side / discharge side shared);
P-connect / discharge terminal negative (shared with charge / discharge).
Tips: the battery pack when the battery voltage, capacity, internal resistance must be a good match, the battery voltage in the rated voltage of about 3.7V appropriate, the group did not output a good battery pack, with 8.4V voltage can be charged.
Package Included:
10PCS*2S 10A 7.4V 8.4V Li-ion Lithium 18650 Battery w/Balance BMS Protection PCB Board
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.